Kb-electronics KBAC-48 Uživatelský manuál stáhnout pdf (Strana 9)

Output Contacts.

Run/Fault Relay

Start/Stop Switch.

Main Speed Potentiometer.

Diagnostic LEDs.

J4: 1X or up to 2X

J9: Normally Open or ClosedJ11: I

t Overload selection.

CON1: Used to connect

optional accessories to the drive.

Stop Contact selection.

Torque selection.

J10: Constant or Variable

J7: Regenerative or

Output Relay Operation selection.

Injection Braking selection.

J8: "Run" or "Fault"

J6: Fixed or Adjustable Boost selection.

Rated Motor RPM Operation selection.

Motor Operation selection.

J5: 60 Hz or 50 Hz

All jumpers and trimpots are shown in factory set positions.

J1: AC Line Input Voltage selection

J2: Motor Horsepower selection

(Models KBAC-24D, 27D only).

J3: Automatic Ride-Through

or Manual Start selection.

Used with optional Run-Stop-Jog Switch Kit.

Adjustable Trimpots

JOG Terminal.

See Section 6.6 on Page 19.

See Section 6.7 on Page 19.

See Section 6.4 on Pages 18 - 19.

See Section 6.5 on Page 19.

See Section 6.1 on Page 18.

See Section 6.2 on Page 18.

See Section 6.3 on Page 18.

See Section 13 on Pages 23 – 26.

See Table 2 on Page 8.

See Section 5.5

See Section 5.9

on Page 17.

on Page 16.

Normally Closed

Red

Normally Open

Relay Common

See Section 5.4 on Pages 15 - 16.

Black

White

See Section 6.10 on Page 20.

See Table 2 on Page 8.

Used for optional

Forward-Stop-Reverse

Switch.

See Section 6.8 on Page 19.

See Section 6.9 on Page 20.

White (Low) (P1)

Violet (High) (P3)

Orange (Wiper) (P2)

See Section 12 on Page 23.

STATUS

POWER

STOP

NCNO COM

FWDCOM RUN REV COM

CON2

JOGP1P3 P2

ACCELMINMAX JOGCLDECEL BOOST

TB2

50Hz

60Hz 1X

J8J9

NCNO F

J11 J10

CT21 VT

CON1

FIX

RGR INJ

ADJ

COMP

Figure 2 – Control Layout

Notes: 1. Layout of Model KBAC-24D varies slightly. 2. On Model KBAC-24D, the JOG and COMP Trimpots are located vertically, along the right edge of the PC board (below the mounting screw). 3. On Model KBAC-24D, Jumper J2 is labeled “1”, “3/4”, “1/2”, “1/4”,

“1/8” (factory set to the “1” position). On Model KBAC-27D, Jumper J2 is labeled “2”, “11⁄2”, “1”, “3/4”, “1/2” (factory set to the “11⁄2” position). On Models KBAC-29, 29 (1P), 45, 48, Jumper J2 is labeled “A”, “B”, “C”, “D”, “E” (factory set according to Table 4 on page 10.

4. On Model KBAC-24D, Jumper J3 is labeled “AUTO” and “MAN”.

1 2 3 4 5 6 7 8 9 10 11 12 13 14 ... 27 28

Komentáře k této Příručce

Žádné komentáře

Kb-electronics KBAC-48 Uživatelský manuál Strana 9

Komentáře k této Příručce

Související produkty a manuály pro Software Kb-electronics KBAC-48